http://nova.newcastle.edu.au/vital/access/services/Feed ${session.getAttribute("locale")} 5 http://nova.newcastle.edu.au/vital/access/manager/Repository/uon:3142 The desorption and subsequent pH-responsive behavior of selectively quaternized poly(2-(dimethylamino)ethyl methacrylate)-block-poly(2-(diethylamino)ethyl methacrylate) (PDMA–PDEA) films at the silica/aqueous solution interface has been characterized. The copolymer films were prepared at pH 9, where micelle-like surface aggregates are spontaneously formed on silica. The subsequent rinse with a copolymer-free electrolyte solution adjusted to pH 9 causes partial desorption of the weakly or non-quaternized copolymers, but negligible desorption for the highly quaternized copolymers. Further rinsing with a pH 4 electrolyte solution results in additional desorption and extension (swelling) of the remaining adsorbed copolymer film normal to the interface. This pH-responsive behavior is reversible for two pH cycles (9–4–9–4) as monitored by both quartz crystal microbalance with dissipation monitoring (QCM-D) and also ζ potential measurements. The magnitude of the pH-responsive behavior depends on the mean degree of quaternization of the PDMA block. Moreover, a combination of contact angle data, ζ potential measurements and in situ atomic force microscopy (AFM) studies indicates that the pH-responsive behavior is influenced not only by the number of cationic binding sites on the adsorbed copolymer chains but also by the adsorbed layer structure. 2010-04-27T05:06:07.815Z ]]> http://nova.newcastle.edu.au/vital/access/manager/Repository/uon:3140 The first in situ proof of the presence of true nanoscale micelle structure within alternating layers of a self-assembled cationic and anionic diblock copolymer micelle−micelle multilayer film is presented using atomic force microscopy. Apparently similar layer morphologies are distinguished by the interaction force curves normal to each layer. The three-dimensional order in these low Tg diblock copolymer films, together with their mechanical resilience and strongly hydrated nature, suggests many new technological applications. 2010-04-27T05:06:03.093Z ]]> http://nova.newcastle.edu.au/vital/access/manager/Repository/uon:4446 The in situ layer-by-layer (LbL) self-assembly of low Tg diblock copolymer micelles onto a flat silica substrate is reported. The copolymers used here were a cationic poly(2-(dimethylamino)ethyl methacrylate)-block-poly(2(diethylamino)ethyl methacrylate) (50qPDMA-PDEA; 50q refers to a mean degree of quaternization of 50 mol% for the PDMA block) and zwitterionic poly(methacrylic acid)-block-poly(2-(diethylamino)ethyl methacrylate) (PMAA-PDEA), which has anionic character at pH 9. Alternate deposition of micelles formed by these two copolymers onto a silica substrate at pH 9 was examined. The in situ LbL buildup of the copolymer micelle films was monitored using ζ potential measurements, optical reflectometry, and a quartz crystal microbalance with dissipation monitoring (QCM-D). For a six layer deposition, complete charge reversal was observed after the addition of each layer. The OR data indicated clearly an increase in adsorbed mass with each additional micelle layer and suggest that some interdiffusion of copolymer chains between layers and/or an increase in the film roughness, and hence in the effective surface area of the micellar multilayers, must take place as the film is built up. QCM-D data indicated that the self-assembled micellar multilayers on a flat silica substrate undergo structural changes over a prolonged period. This is attributed to longer-term interdiffusion of the copolymer chains between the outer two layers after the initial adsorption of each layer is complete. The QCM-D data further suggest that the outer adsorbed layers adopt a progressively more extended conformation, particularly for the higher numbered layers. The morphology of each successive layer was characterized using in situ soft-contact atomic force microscopy, and micelle-like surface aggregates are clearly observed within each layer of the complex film, suggesting the persistence of aggregate structures throughout the multilayer structure. 2010-04-27T04:58:49.233Z ]]> http://nova.newcastle.edu.au/vital/access/manager/Repository/uon:5017 The adsorption of a zwitterionic diblock copolymer, poly(2-(diethylamino)ethyl methacrylate)–block–poly(methacrylic acid) (PDEA₅₉–PMAA₅₀), at the silica/aqueous solution interface has been characterised as a function of pH. In acidic solution, this copolymer forms core–shell micelles with the neutral PMAA chains being located in the hydrophobic cores and the protonated PDEA chains forming the cationic micelle coronas. In alkaline solution, the copolymer forms the analogous inverted micelles with anionic PMAA coronas and hydrophobic PDEA cores. The morphology of the adsorbed layer was observed in situ using soft-contact atomic force microscopy (AFM): this technique suggests the formation of a thin adsorbed layer at pH 4 due to the adsorption of individual copolymer chains (unimers) rather than micelle aggregates. This is supported by the remarkably low dissipation values and the relatively low degrees of hydration for the adsorbed layers, as estimated using a combination of quartz crystal microbalance with dissipation monitoring (QCM-D) and optical reflectometry (OR). In alkaline solution, analysis of the adsorption data suggests a conformation for the adsorbed copolymers where one block projects normal to the solid/liquid interface; this layer consists of a hydrophobic PDEA anchor block adsorbed on the silica surface and an anionic PMAA buoy block extending into the solution phase. Tapping mode AFM studies were also carried out on the silica surfaces after removal from the copolymer solutions and subsequent drying. Interestingly, in these cases micelle-like surface aggregates were observed from both acidic and alkaline solutions. The lateral dimension of the aggregates seen is consistent with the corresponding hydrodynamic diameter of the copolymer micelles in bulk solution. The combination of the in situ and ex situ AFM data provides evidence that, for this copolymer, micelle aggregates are only seen in the ex situ dry state as a result of the substrate withdrawal and drying process. It remains unclear whether these aggregates are caused by micelle deposition at the surface during the substrate withdrawal from the solution or as a result of unimer rearrangements at the drying front as the liquid recedes from the surface. 2010-04-27T04:45:08.213Z ]]>